How to configure UPS with USB connection

I was unable to setup nut on a server for the UPS Eaton 5E with USB connection. All results what did I get was that driver is not running and UPS is not recognized. What kind of driver is suitable for me and what kind of settings? Unit is Eaton 5E.

result of $ lsusb -v

Bus 004 Device 007: ID 0463:ffff MGE UPS Systems UPS
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0 
  bDeviceProtocol         0 
  bMaxPacketSize0         8
  idVendor           0x0463 MGE UPS Systems
  idProduct          0xffff UPS
  bcdDevice            0.01
  iManufacturer           1 
  iProduct                2 
  iSerial                 0 
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           34
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0 
    bmAttributes         0xa0
      (Bus Powered)
      Remote Wakeup
    MaxPower               20mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         3 Human Interface Device
      bInterfaceSubClass      0 No Subclass
      bInterfaceProtocol      0 None
      iInterface              0 
        HID Device Descriptor:
          bLength                 9
          bDescriptorType        33
          bcdHID               1.10
          bCountryCode           33 US
          bNumDescriptors         1
          bDescriptorType        34 Report
          wDescriptorLength     549
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0008  1x 8 bytes
        bInterval              20
Device Status:     0x0001
  Self Powered

Content of /etc/nut/ups.conf

[Eaton5E]
driver = blazer_usb
port = auto

Result of $ upsdrvctl start for usbhid-ups driver:

Network UPS Tools - UPS driver controller 2.4.3
Network UPS Tools - Generic HID driver 0.34 (2.4.3)
USB communication driver 0.31
No matching HID UPS found
Driver failed to start (exit status=1)

Result of $ upsdrvctl start for blazer_usb driver:

Network UPS Tools - UPS driver controller 2.4.3
Network UPS Tools - Megatec/Q1 protocol USB driver 0.03 (2.4.3)
No supported devices found. Please check your device availability with 'lsusb'
and make sure you have an up-to-date version of NUT. If this does not help,
try running the driver with at least 'subdriver', 'vendorid' and 'productid'
options specified. Please refer to the man page for details about these options
(man 8 blazer).

Driver failed to start (exit status=1)

Update: I tried to connect a desktop linux Xubuntu 12.04, which detected the UPS and UPS vendor via usbhid-ups driver, but did not detected any battery state and shows battery as discharged (what is not true, server is running on it several minutes with no troubles) and fiel technology as Unknown.

Try to use the config from this blogger: http://risc-a-day.blogspot.hu/2014/09/getting-my-ups-to-work-with-linux.html

(Excerpts:

lsusb
...
Bus 008 Device 002: ID 0463:ffff MGE UPS Systems UPS

... edit /etc/nut/ups.conf and add section for the UPS device itself:

...

[myups]
    driver = usbhid-ups
    port = auto
    vendorid = 0463
    pollfreq = 30

...

$ sudo upsdrvctl start

...

$ upsc myups

battery.charge: 75
battery.runtime: 1737
battery.type: PbAc
device.mfr: EATON
device.model: 5E 1100i
device.type: ups
driver.name: usbhid-ups
driver.parameter.pollfreq: 30
driver.parameter.pollinterval: 2
driver.parameter.port: auto
driver.parameter.vendorid: 0463
driver.version: 2.6.4
driver.version.data: MGE HID 1.31
driver.version.internal: 0.37
input.voltage: 229.0
outlet.1.status: on
outlet.desc: Main Outlet
outlet.id: 1
outlet.switchable: no
output.frequency: 49.9
output.frequency.nominal: 50
output.voltage: 233.0
output.voltage.nominal: 230
ups.beeper.status: enabled
ups.delay.shutdown: 20
ups.firmware: 01.04.0018
ups.load: 12
ups.mfr: EATON
ups.model: 5E 1100i
ups.power.nominal: 1100
ups.productid: ffff
ups.start.battery: yes
ups.status: OL CHRG
ups.timer.shutdown: -1
ups.vendorid: 0463

)

once try these things,

You can use lsusb to find out the bus and device number

Then change permission to the device

        chmod 0666 /dev/bus/usb/[bus number]/[device number]

as for details go with rouble starting Network UPS Tools with a Eaton 3S UPS