What is the Linux equivalent to DOS pause?

Solution 1:

read does this:

user@host:~$ read -n1 -r -p "Press any key to continue..." key
[...]
user@host:~$ 

The -n1 specifies that it only waits for a single character. The -r puts it into raw mode, which is necessary because otherwise, if you press something like backslash, it doesn't register until you hit the next key. The -p specifies the prompt, which must be quoted if it contains spaces. The key argument is only necessary if you want to know which key they pressed, in which case you can access it through $key.

If you are using Bash, you can also specify a timeout with -t, which causes read to return a failure when a key isn't pressed. So for example:

read -t5 -n1 -r -p 'Press any key in the next five seconds...' key
if [ "$?" -eq "0" ]; then
    echo 'A key was pressed.'
else
    echo 'No key was pressed.'
fi

Solution 2:

I use these ways a lot that are very short, and they are like @theunamedguy and @Jim solutions, but with timeout and silent mode in addition.

I especially love the last case and use it in a lot of scripts that run in a loop until the user presses Enter.

Commands

• Enter solution

  read -rsp $'Press enter to continue...\n'
  

• Escape solution (with -d $'\e')

  read -rsp $'Press escape to continue...\n' -d $'\e'
  

• Any key solution (with -n 1)

  read -rsp $'Press any key to continue...\n' -n 1 key
  # echo $key
  

• Question with preselected choice (with -ei $'Y')

  read -rp $'Are you sure (Y/n) : ' -ei $'Y' key;
  # echo $key
  

• Timeout solution (with -t 5)

  read -rsp $'Press any key or wait 5 seconds to continue...\n' -n 1 -t 5;
  

• Sleep enhanced alias

  read -rst 0.5; timeout=$?
  # echo $timeout
  

Explanation

-r specifies raw mode, which don't allow combined characters like "\" or "^".

-s specifies silent mode, and because we don't need keyboard output.

-p $'prompt' specifies the prompt, which need to be between $' and ' to let spaces and escaped characters. Be careful, you must put between single quotes with dollars symbol to benefit escaped characters, otherwise you can use simple quotes.

-d $'\e' specifies escappe as delimiter charater, so as a final character for current entry, this is possible to put any character but be careful to put a character that the user can type.

-n 1 specifies that it only needs a single character.

-e specifies readline mode.

-i $'Y' specifies Y as initial text in readline mode.

-t 5 specifies a timeout of 5 seconds

key serve in case you need to know the input, in -n1 case, the key that has been pressed.

$? serve to know the exit code of the last program, for read, 142 in case of timeout, 0 correct input. Put $? in a variable as soon as possible if you need to test it after somes commands, because all commands would rewrite $?

Solution 3:

read without any parameters will only continue if you press enter. The DOS pause command will continue if you press any key. Use read –n1 if you want this behaviour.

Solution 4:

This worked for me on multiple flavors of Linux, where some of these other solutions did not (including the most popular ones here). I think it's more readable too...

echo Press enter to continue; read dummy;

Note that a variable needs to be supplied as an argument to read.

Solution 5:

read -n1 is not portable. A portable way to do the same might be:

(   trap "stty $(stty -g;stty -icanon)" EXIT
    LC_ALL=C dd bs=1 count=1 >/dev/null 2>&1
)   </dev/tty

Besides using read, for just a press ENTER to continue prompt you could do:

sed -n q </dev/tty