Is there a software utility to adjust screen gamma/brightness/contrast?

Solution 1:

Redshift

I have been using this. It's very nice.

sudo apt install redshift

To use it just type in the terminal redshift.

gtk-redshift is just the GUI, not required.

f.lux is also an option (proprietary, closed source).

Solution 2:

To adjust gamma (which is a good substitute for adjusting contrast), you can write:

xgamma -gamma 0.3

on the command line (Terminal). You should see a very noticeable difference. Experiment with different values.

1.0 is the normal (uncorrected) gamma value. Setting a lower gamma (for example 0.7) will increase the contrast of bright luminances, which makes midtones darker and decreases white washing. Setting a higher gamma (for example 1.5) will make midtones brighter and increase the contrast of dark luminances, but also increases white washing.

For my inexpensive laptop, I use gamma 0.8 to compensate for the too bright factory setting for the LCD and I find that the gamma correction helps with color reproduction too, which is nice because so far I haven't managed to get any color calibration working on this LCD.

Solution 3:

TL;DR

Use:

• xbacklight
• ddccontrol
• redshift
• xgamma

Backlight vs pixel values

First and most importantly, if at all possible adjust the display backlight, rather than using software correction of pixel values. If you dim the backlight you still get full or near-full dynamic range, giving you a clearer, "deeper" image that tends to be more readable.

Software adjustment can't make the blacks darker, it just makes white greyer and reduces contrast. So instead of using pixel values from 0-255 it might use from 0-180 for example. Everything looks flatter.

A tool like Redshift can be useful for changing colour balance, but as much as possible you should try to change brightness with backlight adjustment.

DDC/CI

Last I checked, most displays unfortunately do(did?) not implement backlight control from software. There's a standard for it, DDC/CI but adoption has been limited. Try the ddccontrol tool with your monitor and see if you have any luck.

I've only seen it in very high end displays intended for calibrated photo and video work ... and even many of those use a USB connection and custom USB HID based driver instead of the DDC/CI standard. I'm pretty outdated though, and the linked article claims that basic options like brightness and contrast are widely supported now.

Fake brightness controls on cheap displays

Some cheap displays don't support backlight control at all. The brightness controls on the display just adjust the pixel values on the LCD, just like software control does. Do not use these controls if you have such a monitor; it's usually better to do the correction in software, certainly no worse.

Doesn't go dim enough?

All too many displays do have backlight control, but minimum brightness is still eye-searing. They can sometimes be modified, but otherwise your best bet is setting them to minimum backlight brightness and then living with changing pixel values to get them even dimmer.

It really annoys me that displays have such a limited backlight intensity range, often artifically and arbitrarily limited, starting at eye-searing to "the power of a million suns". I look for dim backlights when I'm speccing out displays to buy.

Laptops

On a laptop, the backlight is usually controlled by software. Yay!

(If your laptop is still old enough to use APM control instead of ACPI or custom drivers, get off my lawn).

The details are somewhat driver and software specific, but your laptop should offer convenient Fn keys that make it easy, and the OS should have a simple display brightness slider. The xbacklight utility offers a convenient command line control for this, though on my system it doesn't seem to like to go below 1% brightness and goes straight to black.

I twiddle the driver controls because my T460 is very bright - wonderful during the day, but horrible at night. The minimum brightness step offered by the fn key adjustments is still way too bright, but the driver provides much finer grained control. xbacklight only lets me get down to brighness 8/255 and I'd like So I tell it to run at 4/255 brightness:

echo 4 | sudo tee -a  /sys/class/backlight/intel_backlight/brightness

This works on a Lenovo T460 with Intel graphics, but other drivers and hardware may have different entries under /sys/class/backlight with different range limits etc.

The arch wiki has some useful info.

Gamma adjustment

When you lower brightness you might want to increase contrast in software a bit, especially if working on text. It'll cost you image quality, but gain you readability at low brightness. The xgamma utility will let you do that, e.g.

xgamma -gamma 0.8

Someone want to patch Redshift with brightness controls?

So, you know what'd be cool?

If Redshift could fade display brightness based on an ambient light sensor and/or time of day, via the same xrandr controls used by xbacklight.

Solution 4:

The software you're looking for is Redshift (install):

Redshift adjusts the color temperature of your screen according to your surroundings. This may help your eyes hurt less if you are working in front of the screen at night.

Solution 5:

XRandR

xrandr is very powerful but in this way similar to xgamma, also let you select the level for each three colors. For example

xrandr --output HDMI2  --gamma 1:1:1
                             # R G B

Will set gamma to the default value (1 for each color channel). Select the appropriate output by choosing from one of the connected devices, listed with just xrandr (or xrandr | grep -vE "^ " | grep -v disconnect).

Note: if you use Redshift or flux (closed-source) they will override xrandr setup.

From man page:

• --gamma red:green:blue Set the specified floating-point values as gamma correction on the crtc currently attached to this output. Note that you cannot get two different values for cloned outputs (i.e.: which share the same crtc) and that switching an output to another crtc doesn't change the crtc gamma corrections at all.
• --brightness brightness Multiply the gamma values on the crtc currently attached to the output to specified floating value. Useful for overly bright or overly dim outputs.
  Note: his is a software only modification, if your hardware has support to actually change the brightness see this answer.