Installing D-Link DWA-131 (13.10)

I found this thread:

https://askubuntu.com/questions/439901/how-do-i-install-a-d-link-dwa-131

But it has been closed. One comment referred to this guide:

http://bernaerts.dyndns.org/linux/74-ubuntu/277-ubuntu-precise-dwa-131-rev-b1

But it doesn't work.

To begin, the guide is for this:

package barcode showing H/W Ver.:B1 F/W Ver.:2.00

But my package has

package barcode showing H/W Ver.:B1 F/W Ver.:2.01

As for the vendor ID of

2001 and Device ID 330d

I can't see either of those numbers on the box or in the example shown in the guide.

Next, the guide talks about updating the kernel but the kernel I am running is already higher:

My kernel

Linux connor 3.11.0-19-generic #33-Ubuntu SMP Tue Mar 11 18:48:34 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux

My version

connor@connor:~$ lsb_release -a
No LSB modules are available.
Distributor ID: Ubuntu
Description:    Ubuntu 13.10
Release:    13.10
Codename:   saucy

When I do the next step sudo modprobe rtl8192cu swenc=1 there's no output

Then the next echo "2001 330D" | sudo tee /sys/bus/usb/drivers/rtl8192cu/new_id this is the output

2001 330D

My lsusb

Bus 003 Device 006: ID 2001:330d D-Link Corp. 

I've also been trying this thread

http://ubuntuforums.org/showthread.php?t=2200493&page=2&p=12978483#post12978483

I did the driver update instruction, it seemed to update but when I reboot still no light coming on the USB device

Next I try this command

lsmod
iwconfig
ifconfig -a
cat /etc/resolv.conf

This is the output

Module                  Size  Used by
rfcomm                 69130  0 
crct10dif_pclmul       14289  0 
crc32_pclmul           13113  0 
lrw                    13286  1 aesni_intel
gf128mul               14951  1 lrw
ath9k                 155907  0 
ath9k_common           13859  1 ath9k
ath9k_hw              444732  2 ath9k_common,ath9k
ath                    23827  3 ath9k_common,ath9k,ath9k_hw
mac80211              597268  1 ath9k
cfg80211              480503  3 ath,ath9k,mac80211

connor@connor:~$ iwconfig

wlan0     IEEE 802.11bgn  ESSID:off/any  
          Mode:Managed  Access Point: Not-Associated   Tx-Power=16 dBm   
          Retry  long limit:7   RTS thr:off   Fragment thr:off
          Power Management:off

connor@connor:~$ ifconfig -a

wlan0     Link encap:Ethernet  HWaddr 24:fd:52:79:9c:53  
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 

Does anyone know how to get this device working?

Update:

lsusb output, with/without USB modem attached (difference only)

connor@connor:~$ lsusb

Bus 003 Device 013: ID 2001:330d D-Link Corp. 

dmesg output, last 20 lines

Am on 14.04 with same DWA131-B1 adapter, used this driver (follow instructions there) and added 8192cu to /etc/modules and

echo "2001 330D" | sudo tee /sys/bus/usb/drivers/rtl8192cu/new_id 

to /etc/rc.local (note that this still uses the 'rtl') as per this so far stable and fast without swenc=1