CentOS: eth0 not starting on boot

Whenever I reboot a CentOS Hyper-V VM, eth0 does not start automatically. All I need to do is perform ifup eth0 and all is fixed, but that isn't feasible from ssh! I am starting in runlevel 3.

[root@localhost ~]# cat /etc/*release*
CentOS release 6.2 (Final)

After I perform ifup eth0 on the console:

[root@localhost ~]# ifconfig
eth0      Link encap:Ethernet  HWaddr 00:15:5D:2B:2B:07
      inet addr:10.10.0.3  Bcast:10.10.0.255  Mask:255.255.255.0
      inet6 addr: fe80::215:5dff:fe2b:2b07/64 Scope:Link
      UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
      RX packets:34 errors:0 dropped:0 overruns:0 frame:0
      TX packets:49 errors:0 dropped:0 overruns:0 carrier:0
      collisions:0 txqueuelen:1000
      RX bytes:4656 (4.5 KiB)  TX bytes:6399 (6.2 KiB)
      Interrupt:9 Base address:0xa000

[root@localhost ~]# cat /etc/sysconfig/network-scripts/ifcfg-eth0
DEVICE=eth0
BOOTPROTO=none
IPADDR=10.10.0.3
NETMASK=255.255.255.0
GATEWAY=10.10.0.1
USERCTL=no
ONBOOT=yes

[root@localhost ~]# chkconfig --list | grep network
network         0:off   1:off   2:on    3:on    4:on    5:on    6:off

After trying to turn off Network Manager

[root@localhost ~]# chkconfig NetworkManager off
error reading information on service NetworkManager: No such file or directory
[root@localhost ~]# service NetworkManager status
NetworkManager: unrecognized service

[root@localhost ~]# grep eth0 /var/log/messages
Jul  7 02:12:44 localhost kernel: eth0: Digital DS21140 Tulip rev 32 at MMIO 0xfebff000, 00:15:5d:2b:2b:07, IRQ 9.
Jul  7 02:13:15 localhost kernel: eth0: Using EEPROM-set media 100baseTx-FDX.

[root@localhost ~]# dmesg | grep eth0
eth0: Digital DS21140 Tulip rev 32 at MMIO 0xfebff000, 00:15:5d:2b:2b:07, IRQ 9.
eth0: Using EEPROM-set media 100baseTx-FDX.
eth0: no IPv6 routers present

[root@localhost ~]# ifup eth0
/etc/sysconfig/network-scripts/ifup-ipv6: line 56: /etc/sysconfig/network: No such file or directory
/etc/sysconfig/network-scripts/ifup-aliases: line 125: /etc/sysconfig/network: No such file or directory

Solution 1:

Hmm. From your last message, look for the /etc/sysconfig/network file.

I have:

$ cat /etc/sysconfig/network
NETWORKING=yes

You can also have (on my CentOS 5 box):

NETWORKING=yes
HOSTNAME=foo.example.org
GATEWAY=192.168.1.1

Documentation is here (at least for 5, which should be very similar)

I'm not sure what the default is for the "NETWORKING" setting. It's possible it's "no" and that's why it's not starting on boot.

Solution 2:

Open /etc/sysconfig/network-scripts/ifcfg-eth0 file and replace line

ONBOOT=no

with

ONBOOT=yes

save and exit the file, and restart the linux system.