What is causing "Unable to allocate memory for pool" in PHP?
Using a TTL of 0 means that APC will flush all the cache when it runs out of memory. The error don't appear anymore but it makes APC far less efficient. It's a no risk, no trouble, "I don't want to do my job" decision. APC is not meant to be used that way. You should choose a TTL high enough so the most accessed pages won't expire. The best is to give enough memory so APC doesn't need to flush cache.
Just read the manual to understand how ttl is used : http://www.php.net/manual/en/apc.configuration.php#ini.apc.ttl
The solution is to increase memory allocated to APC. Do this by increasing apc.shm_size.
If APC is compiled to use Shared Segment Memory you will be limited by your operating system. Type this command to see your system limit for each segment :
sysctl -a | grep -E "shmall|shmmax"
To alocate more memory you'll have to increase the number of segments with the parameter apc.shm_segments.
If APC is using mmap memory then you have no limit. The amount of memory is still defined by the same option apc.shm_size.
If there's not enough memory on the server, then use filters option to prevent less frequently accessed php files from being cached.
But never use a TTL of 0.
As c33s said, use apc.php to check your config. Copy the file from apc package to a webfolder and point browser to it. You'll see what is really allocated and how it is used. The graphs must remain stable after hours, if they are completly changing at each refresh, then it means that your setup is wrong (APC is flushing everything). Allocate 20% more ram than what APC really use as a security margin, and check it on a regular basis.
The default of allowing only 32MB is ridiculously low. PHP was designed when servers were 64MB and most scripts were using one php file per page. Nowadays solutions like Magento require more than 10k files (~60Mb in APC). You should allow enough memory so most of php files are always cached. It's not a waste, it's more efficient to keep opcode in ram rather than having the corresponding raw php in file cache. Nowadays we can find dedicated servers with 24Gb of memory for as low as $80/month, so don't hesitate to allow several GB to APC. I put 2GB out of 24GB on a server hosting 5Magento stores and ~40 wordpress website, APC uses 1.2GB. Count 64MB for Magento installation, 40MB for a Wordpress with some plugins.
Also, if you have developpment websites on the same server. Exclude them from cache.
Probably is APC related.
For the people having this problem, please specify you .ini settings. Specifically your apc.mmap_file_mask setting.
For file-backed mmap, it should be set to something like:
apc.mmap_file_mask=/tmp/apc.XXXXXX
To mmap directly from /dev/zero, use:
apc.mmap_file_mask=/dev/zero
For POSIX-compliant shared-memory-backed mmap, use:
apc.mmap_file_mask=/apc.shm.XXXXXX
solution for me:
- apc.ttl=0
- apc.shm_size=anything you want
edit start
warning!
@bokan indicated me that i should add a warning here.
if you have a ttl of 0 this means the every cached item can be purged immediately. so if you have a small cache size like 2mb and a ttl of 0 this would render the apc useless, because the data in the cache gets always overwritten.
lowering the ttl means only that the cache cannot become full, only with items which can't be replaced.
so you have to choose a good balance between ttl and cache size.
in my case i had a cache size of 1gb, so it was more than enough for me.
edit end
had the same issue on centos 5 with php 5.2.17 and noticed that if the cache size is small and the ttl parameter is "high" (like 7200) while having a lot of php files to cache, then the cache fills up quite fast and apc doesn't find anything which it can remove because all files in the cache still fit in the ttl.
increasing the memory size is only a part solution, you still run in this error if you cache fills up and all files are within the ttl.
so my solution was to set the ttl to 0, so apc fills up the cache an there is allways the possibility for apc to clear some memory for new data.
hope that helps
edit: see also: http://pecl.php.net/bugs/bug.php?id=16966
download http://pecl.php.net/get/APC extract and run the apc.php, there you have a nice diagram how your cache usage look like
Running the apc.php script is key to understanding what your problem is, IMO. This helped us size our cache properly and for the moment, seems to have resolved the problem.
For newbies like myself, these resources helped:
Finding the apc.ini file to make the changes recommended by c33s above, and setting recommended amounts: http://www.untwistedvortex.com/optimizing-tuning-apc-alternate-php-cache/
Understanding what apc.ttl is: http://www.php.net/manual/en/apc.configuration.php#ini.apc.ttl
Understanding what apc.shm_size is: http://www.php.net/manual/en/apc.configuration.php#ini.apc.shm-size