qemu-kvm/virsh: No network connectivity whilst using bridged networking
I'm having an issue with performing virtualisation via libvirt/qemu-kvm, in which my set up for bridged networking doesn't appear to be working correctly. I've followed every tutorial I can find and spent hours and hours going through forums, but currently to no avail.
Both the host and guest are using Centos6.
Here's the set up for the host:
[root@node2 ~]# ifconfig -a
bridge0 Link encap:Ethernet HWaddr BC:30:5B:E8:C0:4F
inet addr:10.59.190.253 Bcast:10.59.190.255 Mask:255.255.255.0
inet6 addr: fe80::be30:5bff:fee8:c04f/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:5315 errors:0 dropped:0 overruns:0 frame:0
TX packets:3350 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:316961 (309.5 KiB) TX bytes:3943630 (3.7 MiB)
eth0 Link encap:Ethernet HWaddr BC:30:5B:E8:C0:4F
inet6 addr: fe80::be30:5bff:fee8:c04f/64 Scope:Link
UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1
RX packets:5286 errors:0 dropped:0 overruns:0 frame:0
TX packets:5325 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:409939 (400.3 KiB) TX bytes:4095006 (3.9 MiB)
Interrupt:16 Memory:c0000000-c0012800
eth1 Link encap:Ethernet HWaddr BC:30:5B:E8:C0:50
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:17 Memory:c2000000-c2012800
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:28 errors:0 dropped:0 overruns:0 frame:0
TX packets:28 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:2832 (2.7 KiB) TX bytes:2832 (2.7 KiB)
sit0 Link encap:IPv6-in-IPv4
NOARP MTU:1480 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
vnet0 Link encap:Ethernet HWaddr FE:54:00:3A:C5:C9
inet6 addr: fe80::fc54:ff:fe3a:c5c9/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:492 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:500
RX bytes:0 (0.0 b) TX bytes:29516 (28.8 KiB)
I have two physical adapters, eth0 and eth1. eth1 is currently unplugged and not being used in this set up. eth0 is bridged to bridge0. bridge0 is using DHCP to get its network configuration. The adapters use the following configurations:
[root@node2 network-scripts]# cat ifcfg-eth0
DEVICE="eth0"
NM_CONTROLLED="no"
ONBOOT=yes
HWADDR=BC:30:5B:E8:C0:4F
BRIDGE=bridge0
[root@node2 network-scripts]# cat ifcfg-bridge0
DEVICE=bridge0
ONBOOT=yes
TYPE=Bridge
BOOTPROTO=dhcp
DELAY=0
NM_CONTROLLED=no
...and iptables set up as follows:
[root@node2 network-scripts]# iptables --list-rules
-P INPUT ACCEPT
-P FORWARD ACCEPT
-P OUTPUT ACCEPT
-A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT
-A INPUT -p icmp -j ACCEPT
-A INPUT -i lo -j ACCEPT
-A INPUT -p tcp -m state --state NEW -m tcp --dport 22 -j ACCEPT
-A INPUT -p tcp -m state --state NEW -m tcp --dport 5900 -j ACCEPT
-A INPUT -j REJECT --reject-with icmp-host-prohibited
-A FORWARD -m physdev --physdev-is-bridged -j ACCEPT
-A FORWARD -m physdev --physdev-is-bridged -j ACCEPT
-A FORWARD -j REJECT --reject-with icmp-host-prohibited
So, that's the set up. I then used the following command to create and install a Centos6 guest image:
virt-install --name=centos-bridge-test --disk path=/var/lib/libvirt/images/centos6-minimal,size=5 --vnc --ram=512 --cdrom=/var/lib/libvirt/images/CentOS-6.0-x86_64-minimal.iso --vnclisten=0.0.0.0 -b bridge0
My understanding is that this set-up should have been sufficient for the bridged networking to "just work," however, when I start the guest using the virsh command (virsh start centos-bridge-test) it has no network connectivity.
Here's an xml dump of the libvirt domain:
[root@node2 network-scripts]# virsh dumpxml centos-bridge-test
<domain type='kvm' id='7'>
<name>centos-bridge-test</name>
<uuid>5d611267-2feb-c6f7-7a48-29f9695a4a75</uuid>
<memory>524288</memory>
<currentMemory>524288</currentMemory>
<vcpu>1</vcpu>
<os>
<type arch='x86_64' machine='rhel6.0.0'>hvm</type>
<boot dev='hd'/>
</os>
<features>
<acpi/>
<apic/>
<pae/>
</features>
<clock offset='utc'/>
<on_poweroff>destroy</on_poweroff>
<on_reboot>restart</on_reboot>
<on_crash>restart</on_crash>
<devices>
<emulator>/usr/libexec/qemu-kvm</emulator>
<disk type='file' device='disk'>
<driver name='qemu' type='raw' cache='none'/>
<source file='/var/lib/libvirt/images/centos6-minimal'/>
<target dev='hda' bus='ide'/>
<alias name='ide0-0-0'/>
<address type='drive' controller='0' bus='0' unit='0'/>
</disk>
<disk type='block' device='cdrom'>
<driver name='qemu' type='raw'/>
<target dev='hdc' bus='ide'/>
<readonly/>
<alias name='ide0-1-0'/>
<address type='drive' controller='0' bus='1' unit='0'/>
</disk>
<controller type='ide' index='0'>
<alias name='ide0'/>
<address type='pci' domain='0x0000' bus='0x00' slot='0x01' function='0x1'/>
</controller>
<interface type='bridge'>
<mac address='52:54:00:3a:c5:c9'/>
<source bridge='bridge0'/>
<target dev='vnet0'/>
<alias name='net0'/>
<address type='pci' domain='0x0000' bus='0x00' slot='0x03' function='0x0'/>
</interface>
<serial type='pty'>
<source path='/dev/pts/1'/>
<target port='0'/>
<alias name='serial0'/>
</serial>
<console type='pty' tty='/dev/pts/1'>
<source path='/dev/pts/1'/>
<target port='0'/>
<alias name='serial0'/>
</console>
<input type='mouse' bus='ps2'/>
<graphics type='vnc' port='5900' autoport='yes' listen='0.0.0.0' keymap='en-gb'/>
<video>
<model type='cirrus' vram='9216' heads='1'/>
<alias name='video0'/>
<address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x0'/>
</video>
<memballoon model='virtio'>
<alias name='balloon0'/>
<address type='pci' domain='0x0000' bus='0x00' slot='0x04' function='0x0'/>
</memballoon>
</devices>
<seclabel type='dynamic' model='selinux'>
<label>system_u:system_r:svirt_t:s0:c384,c608</label>
<imagelabel>system_u:object_r:svirt_image_t:s0:c384,c608</imagelabel>
</seclabel>
</domain>
The interface appears to be set up correctly (from looking at the libvirt documentation).
So, whenever I start the guest, there is no network connectivity.
[root@localhost ~]# ifconfig -a
eth0 Link encap:Ehternet HWaddr 52:54:00:3A:C5:C9
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:10 Base address:0x6000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Edit: Note that eth0 is not up here, so I've been running ifup eth0 to get the adapter to come up, which then gives the following output:
[root@localhost ~]# ifconfig -a
eth0 Link encap:Ehternet HWaddr 52:54:00:3A:C5:C9
inet6 addr: fe80::5054:ff:fe3a:c5c9/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets65 errors:0 dropped:0 overruns:0 frame:0
TX packets:5 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:3896 (3.8 KiB) TX bytes:398 (398.0 b)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
...and when I attempt to access the network for either an internal or external address, I get this:
[root@localhost ~]# ping 10.59.190.253
connect: Network is unreachable
[root@localhost ~]# ping www.google.com
ping: unknown host www.google.com
[root@localhost ~]# ping 173.194.66.99
connect: Network is unreachable
Additional Info: The following is some additional information requested form the comments for this question. These commands were run from the host with the guest currently running:
[root@node2 network-scripts]# brctl show
bridge name bridge id STP enabled interfaces
bridge0 8000.bc305be8c04f no eth0
vnet0
[root@node2 network-scripts]# ps -ef | grep qemu
qemu 1597 1 0 11:28 ? 00:00:25 /usr/libexec/qemu-kvm -S -M rhel6.0.0 -enable-kvm -m 512 -smp 1,sockets=1,cores=1,threads=1 -name centos-bridge-test -uuid 5d611267-2feb-c6f7-7a48-29f9695a4a75 -nodefconfig -nodefaults -chardev socket,id=monitor,path=/var/lib/libvirt/qemu/centos-bridge-test.monitor,server,nowait -mon chardev=monitor,mode=control -rtc base=utc -boot c -drive file=/var/lib/libvirt/images/centos6-minimal,if=none,id=drive-ide0-0-0,boot=on,format=raw,cache=none -device ide-drive,bus=ide.0,unit=0,drive=drive-ide0-0-0,id=ide0-0-0 -drive if=none,media=cdrom,id=drive-ide0-1-0,readonly=on,format=raw -device ide-drive,bus=ide.1,unit=0,drive=drive-ide0-1-0,id=ide0-1-0 -netdev tap,fd=20,id=hostnet0 -device rtl8139,netdev=hostnet0,id=net0,mac=52:54:00:3a:c5:c9,bus=pci.0,addr=0x3 -chardev pty,id=serial0 -device isa-serial,chardev=serial0 -usb -vnc 0.0.0.0:0 -k en-gb -vga cirrus -device virtio-balloon-pci,id=balloon0,bus=pci.0,addr=0x4
root 2815 32057 0 14:31 pts/0 00:00:00 grep qemu
I'd really appreciate any help possible at the moment! If you need me to provide any further configurations, etc, please do let me know.
Edit: I'm using a minimal install of Centos6, so I don't have any window manager installed, so I'm trying to do everything via virsh and virsh-install, and would like to try to avoid using virsh-manager. Thanks.
The answer to this issue was that because I'd done a non-graphic install of Centos 6 minimal on the guests, the network interfaces had not been automatically set up to work. My lack of knowledge of virtualisation and Centos meant that I assumed that this would be taken care of for me, but I was incorrect in this assumption.
Fix: I needed to go into ifcfg-eth0 on the guests and turn on ONBOOT=yes and BOOTPROTO=dhcp, then restart the network adapter via ifdown eth0 then ifup eth0. After doing this, the guests received IP addresses and everything worked as expected.