Forwarding ports to guests in libvirt / KVM

How can I forward ports on a server running libvirt/KVM to specified ports on VM's, when using NAT?

For example, the host has a public IP of 1.2.3.4. I want to forward port 80 to 10.0.0.1 and port 22 to 10.0.0.2.

I assume I need to add iptables rules, but I'm not sure where is appropriate and what exactly should be specified.

Output of iptables -L

Chain INPUT (policy ACCEPT)
target     prot opt source               destination         
ACCEPT     udp  --  anywhere             anywhere            udp dpt:domain 
ACCEPT     tcp  --  anywhere             anywhere            tcp dpt:domain 
ACCEPT     udp  --  anywhere             anywhere            udp dpt:bootps 
ACCEPT     tcp  --  anywhere             anywhere            tcp dpt:bootps 

Chain FORWARD (policy ACCEPT)
target     prot opt source               destination         
ACCEPT     all  --  anywhere             10.0.0.0/24         state RELATED,ESTABLISHED 
ACCEPT     all  --  10.0.0.0/24          anywhere            
ACCEPT     all  --  anywhere             anywhere            
REJECT     all  --  anywhere             anywhere            reject-with icmp-port-unreachable 
REJECT     all  --  anywhere             anywhere            reject-with icmp-port-unreachable 

Chain OUTPUT (policy ACCEPT)
target     prot opt source               destination

Output of ifconfig

eth0      Link encap:Ethernet  HWaddr 00:1b:fc:46:73:b9  
          inet addr:192.168.1.14  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fe80::21b:fcff:fe46:73b9/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:201 errors:0 dropped:0 overruns:0 frame:0
          TX packets:85 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:31161 (31.1 KB)  TX bytes:12090 (12.0 KB)
          Interrupt:17 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

virbr1    Link encap:Ethernet  HWaddr ca:70:d1:77:b2:48  
          inet addr:10.0.0.1  Bcast:10.0.0.255  Mask:255.255.255.0
          inet6 addr: fe80::c870:d1ff:fe77:b248/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:0 (0.0 B)  TX bytes:468 (468.0 B)

I'm using Ubuntu 10.04.

Solution 1:

The latest stable release for libvirt for Ubuntu is version 0.7.5, which doesn't have some newer features (i.e. script hooks and network filters) which make automatic network configuration easier. That said, here's how to enable port forwarding for libvirt 0.7.5 on Ubuntu 10.04 Lucid Lynx.

These iptables rules should do the trick:

iptables -t nat -I PREROUTING -p tcp -d 1.2.3.4 --dport 80 -j DNAT --to-destination 10.0.0.1:80
iptables -t nat -I PREROUTING -p tcp -d 1.2.3.4 --dport 22 -j DNAT --to-destination 10.0.0.2:22
iptables -I FORWARD -m state -d 10.0.0.0/24 --state NEW,RELATED,ESTABLISHED -j ACCEPT

The default KVM NAT config provides a rule similar to the 3rd I gave above, but it omits the NEW state, which is essential for accepting incoming connections.

If you write a startup script to add these rules and you're not careful, libvirt 0.7.5 overrides them by inserting its own. So, in order to make sure these rules are applied properly on startup, you need to make sure libvirt has initialized before you insert your rules.

Add the following lines to /etc/rc.local, before the line exit 0:

(
# Make sure the libvirt has started and has initialized its network.
while [ `ps -e | grep -c libvirtd` -lt 1 ]; do
        sleep 1
done
sleep 10
# Set up custom iptables rules.
iptables -t nat -I PREROUTING -p tcp -d 1.2.3.4 --dport 80 -j DNAT --to-destination 10.0.0.1:80
iptables -t nat -I PREROUTING -p tcp -d 1.2.3.4 --dport 22 -j DNAT --to-destination 10.0.0.2:22
iptables -I FORWARD -m state -d 10.0.0.0/24 --state NEW,RELATED,ESTABLISHED -j ACCEPT
) &

The sleep 10 above is a hack to make sure the libvirt daemon has had a chance to initialize its iptables rules before we add our own. I can't wait until they release libvirt version 0.8.3 for Ubuntu.

Solution 2:

There is a way to set up port redirection on the fly when the guest is using user-mode networking, I blogged about it here:

http://blog.adamspiers.org/2012/01/23/port-redirection-from-kvm-host-to-guest/

You can see the details there, but for convenience, here is the solution I figured out:

virsh qemu-monitor-command --hmp sles11 'hostfwd_add ::2222-:22'

This one-liner is a lot easier than the other answers but only works in some scenarios (user mode network stack).

Forwarding ports to guests in libvirt / KVM

Solution 1:

Solution 2:

Related

Recent Posts