Error 54046 occurred at disk power-on lifetime
I am using Ubuntu 20. Few days ago, OS was failed to boot and giving harddisk error. So I boot Ubuntu from PenDrive and run smartctl to perform health check of the disk.
Information of Hard Disk:
smartctl 7.1 2019-12-30 r5022 [x86_64-linux-5.4.0-26-generic] (local build)
Copyright (C) 2002-19, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: WDC WD10JPVX-75JC3T0
Serial Number: WXV1EC4LP8RX
LU WWN Device Id: 5 0014ee 65b053a63
Firmware Version: 01.01A01
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Sun Jul 19 15:52:12 2020 UTC
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (18420) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 206) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x7035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 193 193 051 Pre-fail Always - 123282
3 Spin_Up_Time 0x0027 182 177 021 Pre-fail Always - 1875
4 Start_Stop_Count 0x0032 098 098 000 Old_age Always - 2813
5 Reallocated_Sector_Ct 0x0033 133 133 140 Pre-fail Always FAILING_NOW 2829
7 Seek_Error_Rate 0x002e 163 143 000 Old_age Always - 65535
9 Power_On_Hours 0x0032 090 090 000 Old_age Always - 7829
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 098 098 000 Old_age Always - 2410
191 G-Sense_Error_Rate 0x0032 001 001 000 Old_age Always - 170
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 312
193 Load_Cycle_Count 0x0032 188 188 000 Old_age Always - 37465
194 Temperature_Celsius 0x0022 103 093 000 Old_age Always - 44
196 Reallocated_Event_Count 0x0032 001 001 000 Old_age Always - 2654
197 Current_Pending_Sector 0x0032 001 001 000 Old_age Always - 65318
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 1
200 Multi_Zone_Error_Rate 0x0008 001 001 000 Old_age Offline - 167119
240 Head_Flying_Hours 0x0032 092 092 000 Old_age Always - 5946
241 Total_LBAs_Written 0x0032 200 200 000 Old_age Always - 23841324672
242 Total_LBAs_Read 0x0032 200 200 000 Old_age Always - 37145294344
254 Free_Fall_Sensor 0x0032 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 54049 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 54049 occurred at disk power-on lifetime: 6727 hours (280 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 03 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 90 03 00 00 00 a0 00 01:57:01.384 SET FEATURES [Disable SATA feature]
ef 02 00 00 00 00 a0 00 01:57:01.384 SET FEATURES [Enable write cache]
ef 90 03 00 00 00 a0 00 01:57:00.494 SET FEATURES [Disable SATA feature]
ef 02 00 00 00 00 a0 00 01:57:00.494 SET FEATURES [Enable write cache]
Error 54048 occurred at disk power-on lifetime: 6727 hours (280 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 00 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 02 00 00 00 00 a0 00 01:57:01.384 SET FEATURES [Enable write cache]
ef 90 03 00 00 00 a0 00 01:57:00.494 SET FEATURES [Disable SATA feature]
ef 02 00 00 00 00 a0 00 01:57:00.494 SET FEATURES [Enable write cache]
Error 54047 occurred at disk power-on lifetime: 6727 hours (280 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 03 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 90 03 00 00 00 a0 00 01:57:00.494 SET FEATURES [Disable SATA feature]
ef 02 00 00 00 00 a0 00 01:57:00.494 SET FEATURES [Enable write cache]
ef 90 03 00 00 00 a0 00 01:56:59.625 SET FEATURES [Disable SATA feature]
ef 02 00 00 00 00 a0 00 01:56:59.624 SET FEATURES [Enable write cache]
Error 54046 occurred at disk power-on lifetime: 6727 hours (280 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 00 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 02 00 00 00 00 a0 00 01:57:00.494 SET FEATURES [Enable write cache]
ef 90 03 00 00 00 a0 00 01:56:59.625 SET FEATURES [Disable SATA feature]
ef 02 00 00 00 00 a0 00 01:56:59.624 SET FEATURES [Enable write cache]
Error 54045 occurred at disk power-on lifetime: 6727 hours (280 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
04 61 03 00 00 00 a0 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ef 90 03 00 00 00 a0 00 01:56:59.625 SET FEATURES [Disable SATA feature]
ef 02 00 00 00 00 a0 00 01:56:59.624 SET FEATURES [Enable write cache]
ef 90 03 00 00 00 a0 00 01:56:58.757 SET FEATURES [Disable SATA feature]
ef 02 00 00 00 00 a0 00 01:56:58.756 SET FEATURES [Enable write cache]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Conveyance offline Completed: unknown failure 90% 6694 -
# 2 Extended offline Completed: unknown failure 90% 6694 -
# 3 Short offline Completed: unknown failure 90% 6694 -
# 4 Short offline Completed: unknown failure 90% 6694 -
# 5 Extended offline Completed: unknown failure 90% 5657 -
# 6 Conveyance offline Completed: unknown failure 90% 5657 -
# 7 Extended offline Completed: unknown failure 90% 5656 -
# 8 Conveyance offline Completed: unknown failure 90% 5535 -
# 9 Short offline Completed: unknown failure 10% 5473 -
#10 Extended offline Completed: unknown failure 90% 5309 -
#11 Conveyance offline Aborted by host 90% 5309 -
#12 Short offline Aborted by host 10% 4768 -
#13 Short offline Completed without error 00% 4428 -
#14 Short offline Completed without error 00% 4328 -
#15 Short offline Completed without error 00% 4260 -
#16 Short offline Completed without error 00% 4231 -
#17 Short offline Completed without error 00% 4205 -
#18 Short offline Completed without error 00% 2644 -
#19 Short offline Completed without error 00% 2615 -
#20 Short offline Completed without error 00% 2563 -
#21 Short offline Completed without error 00% 1995 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Error Message
Error 54046 occurred at disk power-on lifetime: 6727 hours (280 days + 7 hours)
Please let me know if more information is required and help me to resolve the issue or repair the disk if possible.
This disk has failed, as indicated in the smartctl output. There is not a "repair" to be done to it. The only thing to be done is to replace the disk. If the disk is still within its warranty period, you can return it to the manufacturer under warranty if you wish and your security policies allow it.